MANUAL | QUICK START GUIDE

iCUE LINK H100i | H115i | H150i | H170i RGB

PERFORMANCE LIQUID CPU COOLER

iCUE_LINK_RGB_AIO_Hero_Large
CORSAIR_iCUE_LINK_Color_Logo_max-1000x400_Uncropped

BEFORE YOU START

NOTE: Most newer PC cases include a CPU cut-out to allow access to the bottom of the motherboard. If your case does not include a cut-out, you will need to remove the motherboard from the case prior to installation. iCUE LINK AIO coolers come with the Intel mounting bracket pre-installed on the pump for quick installation.

INTEL INSTALLATION

INCLUDED HARDWARE

Highlighted parts for Intel installation only.

RGB_AIO_Intel_1200_Stadoffs_A

4x Intel 1200/1150/1151/1155/1156 standoffs

RGB_AIO_Intel_1700_Stadoffs_B

4x Intel 1700 standoffs

RGB_AIO_Intel_Backplate_C

1x Intel backplate
(1700/1200/115x only)

RGB_AIO_Intel_Bracket_D

1x Intel mounting plate
(pre-installed)

RGB_AIO_Thumb_E

4x Thumb nuts

RGB_AIO_AM5_AM4_Standoff_GRAY_F

4x AMD AM5/AM4 standoffs

RGB_AIO_AM5_AM4_Bracket_GRAY_G

1x AMD AM5/AM4
mounting bracket

RGB_AIO_Long_Fan_Screw_H

16x Long fan screws (H100i/H115i)
24x Long fan screws (H150i/H170i)

RGB_AIO_Short_Fan_Screw_I

8x Radiator screws (H100i/H115i)
12x Radiator screws (H150i/H170i)

RGB_AIO_Washer_J

8x Washers (H100i/H115i)
12x Washers (H150i/H170i)

RGB_AIO_QX_Fan_K

2x QX RGB fans (H100i/H115i)
3x QX RGB fans (H150i/H170i)

RGB_AIO_SysHub_L

1x System Hub

RGB_AIO_PWR_Cable_M

1x PCIe power cable

RGB_AIO_MicroUSB_Cable_N

1x Micro USB 2.0 cable

RGB_AIO_Tach_Cable_O

1x Tach cable

RGB_AIO_iCUE_Cables_P

1x iCUE LINK Cable 90° 600mm
2x iCUE LINK Cable 90° 135mm

Blank_frame.max-800x600

1. INSTALL THE BACKPLATE

Adjust backplate (C) for your required socket.

Intel_Backplate_Installation-01

2. INSTALL THE INTEL STANDOFF SCREWS

Attach provided Intel standoff for your socket. Use (A) for LGA 1200 / 115X, (B) for LGA 1700. Tighten all four standoff screws until firmly secured.

Intel_Standoff_Screws

3. INSTALL THE RADIATOR

Install the radiator inside the case with the short screws (I) and washers (J) as shown.

Intel_Fans_Installation-01

4. INSTALL THE PUMP UNIT

Align the bracket and pump over the standoff screws as shown. Attach the thumb nuts (E) to the standoff screws as shown. Tighten the thumb nuts until all four corners are firmly secured.

Intel_Pump_Unit_Installation

AMD AM5 INSTALLATION

INCLUDED HARDWARE

Highlighted parts for AMD AM5/AM4 installation only.

RGB_AIO_Intel_1200_Stadoffs_GRAY_A

4x Intel 1200/1150/1151/1155/1156 standoffs

RGB_AIO_Intel_1700_Stadoffs_GRAY_B

4x Intel 1700 standoffs

RGB_AIO_Intel_Backplate_GRAY_C

1x Intel backplate
(1700/1200/115x only)

RGB_AIO_Intel_Bracket_GRAY_D

1x Intel mounting plate
(pre-installed)

RGB_AIO_Thumb_E

4x Thumb nuts

RGB_AIO_AM5_AM4_Standoff_F

4x AMD AM5/AM4 standoffs

RGB_AIO_AM5_AM4_Bracket_G

1x AMD AM5/AM4
mounting bracket

RGB_AIO_Long_Fan_Screw_H

16x Long fan screws (H100i/H115i)
24x Long fan screws (H150i/H170i)

RGB_AIO_Short_Fan_Screw_I

8x Radiator screws (H100i/H115i)
12x Radiator screws (H150i/H170i)

RGB_AIO_Washer_J

8x Washers (H100i/H115i)
12x Washers (H150i/H170i)

RGB_AIO_QX_Fan_K

2x QX RGB fans (H100i/H115i)
3x QX RGB fans (H150i/H170i)

RGB_AIO_SysHub_L

1x System Hub

RGB_AIO_PWR_Cable_M

1x PCIe power cable

RGB_AIO_MicroUSB_Cable_N

1x Micro USB 2.0 cable

RGB_AIO_Tach_Cable_O

1x Tach cable

RGB_AIO_iCUE_Cables_P

1x iCUE LINK Cable 90° 600mm
2x iCUE LINK Cable 90° 135mm

Blank_frame.max-800x600

1. INSTALL THE AMD AM5/AM4 MOUNTING BRACKET

Remove the integrated Intel mounting bracket (Figure 1). Install the AMD AM5/AM4 bracket by pushing both sides into the slot on the pump until secure (Figure 2).

NOTE: It is important that the AMD AM5/AM4 retention bracket be evenly secured on all sides before installation.
AMD_Bracket_Installation

2. PREPARE THE MOTHERBOARD FOR INSTALLATION

Remove the existing AMD AM5/AM4 mounting brackets shown.

AMD_Prepare_Motherboard_Installation-01

3. INSTALL THE AMD AM5/AM4 STANDOFF SCREWS

Attach the provided AM5/AM4 standoffs to the CPU socket. Tighten all four standoff screws until firmly secure.

AMD_AM5_AM4_Standoff_Screws

4. INSTALL THE RADIATOR

Install the radiator inside the case with the short screws (I) and washers (J) as shown.

Intel_Fans_Installation-01

5. INSTALL THE PUMP UNIT

Align the bracket with the AMD AM5/AM4 standoffs as shown. Tighten the thumb nuts (E) until secure.

AMD_AM4AM5_Pump_Unit_Installation

SYSTEM HUB INSTALLATION

iCUE_LINK_CON_1
iCUE_LINK_CON_2

Connect one end of the 135mm iCUE LINK cable with 90° connectors (P) to the distribution hub and the other end to a QX RGB fan mounted on the radiator. Connect the 600mm iCUE LINK cable (P) into an available iCUE LINK port on the distribution hub.

Connect the other end of the 600mm iCUE LINK cable (P) into an available port in the System Hub (L).

2. CONNECT SYSTEM HUB TO USB AND POWER

iCUE_LINK_CON_3
iCUE_LINK_CON_4

Connect the 6-pin microfit connector (M) into
the System Hub (L).

Connect the 6-pin PCIe connector (M) into a dedicated PCIe power cable from the power supply.

iCUE_LINK_CON_5
9pin_MicroUSB_2

Connect the micro-USB cable (N) into the System Hub (L).

Connect the 9-pin USB 2.0 connector (N) into a USB 2.0 header on the motherboard.

iCUE_LINK_CON_6
iCUE_LINK_CONNECTION_6_1

Connect the 2-pin, 1-wire tach cable (O) into the System Hub (L).

Connect the 3-pin, 1-wire tach cable (O) into CPU_FAN header on the motherboard.

3. MOUNT THE SYSTEM HUB

Mount the System Hub inside the case magnetically or with the supplied tape.


SOFTWARE SETUP

VIDEO TUTORIAL

See our comprehensive iCUE setup video guide. This visual guide provides a step-by-step walkthrough of iCUE setup detailed in the writing below.



Follow the step-by-step instructions below to set up your device in iCUE. If you already followed the video above, you can skip this step.

Install iCUE

CORSAIR_iCUE_Color_Logo_max-1000x400_Uncropped

Update iCUE

  • Once iCUE is installed run the software. If a newer iCUE version is available or if any of the connected devices need a firmware update, you will be prompted to perform an update via a notification in the top right corner. You can also click the settings (cog wheel icon in the top right corner) and check for the software and firmware updates manually.
iCUE AIO_RGB Update

Quick lighting setup

  • Select the predefined Murals effects from the iCUE Home screen to quickly change the lighting effects.
iCUE AIO_RGB HOME

1. LIGHTING SETUP

Lighting setup

The Lighting Setup page will display all iCUE LINK devices connected to the System Hub and allow you to re-order them to better match the physical placement inside your system.

  • Mouseover the System Hub tile and select Lighting setup.
iCUE AIO_RGB HOME_2
  • Re-arrange your iCUE LINK devices to match your setup.
iCUE_Setup_3

Lighting effects

Choose what lighting effect will be displayed when the iCUE software is running:

  • Select either the iCUE LINK RGB AIO or QX RGB from the navigation bar.
  • Click "Lighting Effects" to access the lighting effects page and select the desired lighting effect.
  • Click the "+" icon under "Lighting Layers" to add additional lighting effects.
iCUE AIO_RGB Lighting_Effects

Hardware lighting

Choose what lighting effects will be displayed when the iCUE software is not running, usually during computer startup phase:

  • Select either the iCUE LINK RGB AIO or QX RGB from the navigation bar.
  • Click "Hardware Lighting" and select the desired lighting effect.
iCUE AIO_RGB Hardware_Lighting

2. COOLING SETUP

AIO fans setup

Identify which fan(s) are mounted on the radiator. iCUE will automatically assign the AIO-based fan curve for the selected fans.

  • Select the iCUE LINK RGB AIO from the navigation bar.
  • Click “Fans Setup” and click "Run Wizard".
  • Select the fan(s) that are mounted on the radiator by clicking on the UI then click "finish".
iCUE AIO_RGB Fans_Setup

Cooling performance

Select your desired cooling presets for any other fans connected to the System Hub between Quiet, Balanced, Extreme, or create your own curve:

  • Select either the iCUE LINK RGB AIO or QX RGB from the navigation bar.
  • Click "Cooling" to access the cooling performance page.
  • Select the desired cooling preset for each device.
  • Click the "+" icon under "Cooling Presets" to create a custom fan curve.
iCUE_Setup_8

3. ADDITIONAL SETUP

Visit our CORSAIR LAB Youtube channel and Explorer page for additional setup, configuration and tips:

CORSAIR LAB Youtube channel

CORSAIR EXPLORER web page


FAQ

How do I know the direction of the airflow of the fan?

FAQ_image-01_1

An arrow located on the side of the fan indicates the direction of airflow.



Can I reuse the pre-applied thermal paste on the cooler for re-installation?

Re-installation of the iCUE LINK RGB CPU cooler will require you clean off the pre-applied thermal paste and apply a new layer of thermal paste. We recommend using CORSAIR XTM70, sold separately.



What orientation should I install my radiator?

FAQ_image-02_2

For optimal performance, we recommend installing the radiator with the tubes positioned at the bottom of the case (Figure 1). However, you have the flexibility to install the radiator in various orientations, including an inverted position. Please ensure that the highest point of the radiator is elevated above the level of the CPU pump, regardless of the installation orientation (Figure 2).



My cooler and fans are blinking red or not functioning. What do I do?

If the fans on your system are blinking red, this is an indication that too many iCUE LINK devices are connected to a single port on the System Hub. The maximum number of devices that can be connected to a single port is 7. To resolve this issue, please distribute the iCUE LINK devices across both available ports on the System Hub. This will ensure adequate power distribution to all connected devices.


If you continue to experience issues or find that the fans are not functioning at all, please perform the following:

  • Double check all connections between the cooler and fans.
  • Ensure that the cooler is updated to the most recent firmware via iCUE.

If this does not resolve your problems, please open a support ticket or contact our customer support team for further troubleshooting and assistance at https://help.corsair.com/hc/requests/new.



What should I do if my cooler backplate feels loose after installation?

It is common for your cooler backplate to feel loose after you install in into your motherboard for the first time. Once you have seated and tightened down the cooler pump, it will pull the backplate to the motherboard and apply pressure on the socket via the cooler.

IMPORTANT: Do NOT, under any circumstances, add additional washers and spacers to your backplate to decrease play in the backplate. Doing so will increase the mounting pressure to the retention kit and potentially damage your retention kit, motherboard or socket.



What should I do if I lost or broke a specific part or accessory from the iCUE LINK RGB liquid CPU cooler kit?

Replacement parts for iCUE LINK RGB liquid CPU coolers are sold through the CORSAIR webstore.




WARRANTY

Warranty_6

All CORSAIR iCUE LINK coolers have a 6-year warranty.


LEGAL

© 2023 CORSAIR MEMORY, Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks of CORSAIR in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured.


POWER RATING

System Hub Output rating: 12Vdc 7A (per port)

QX RGB Input rating: 12Vdc 1.02A

QX RGB Output rating: 12Vdc 0.2A (no load)