MANUAL | QUICK START GUIDE
iCUE LINK LX RGB
PWM FANS
CONTENTS
Expansion Fan
- One (1) Fan
- One (1) iCUE LINK Cable
- Two (2) Connectors
- Four (4) QuikTurn Mounting Screws
120mm Starter Kit
- Three (3) Fans
- iCUE LINK System Hub
- Two (2) iCUE LINK Cables
- One (1) Power Cable
- One (1) Micro-USB Cable
- Four (4) Connectors
- Twelve (12) QuikTurn Mounting Screws
140mm Starter Kit
- Two (2) Fans
- iCUE LINK System Hub
- Two (2) iCUE LINK Cables
- One (1) Power Cable
- One (1) Micro-USB Cable
- Two (2) Connectors
- Eight (8) QuikTurn Mounting Screws
GETTING TO KNOW YOUR LX RGB FANS
- iCUE LINK LX RGB Fan
- iCUE LINK System Hub
- QuikTurn Mounting Screws
- Active Bridge Connector
- Passive Connector
- iCUE LINK Cable
- Micro-USB Cable
- Power Cable
- Active Port
- Passive Port
GETTING TO KNOW YOUR iCUE LINK SYSTEM HUB
I. Active Port
K. Power Input
L. USB Input
M. Tach Output
FAN INSTALLATION
BEFORE YOU START
STARTER KIT
This section will provide a brief guide on how to install your LX RGB Starter Kit.
Create or Add Into a Fan Group
Connect the LX RGB fan into an existing fan group by aligning and inserting the connectors into the open active (I) and passive ports (J).
Set Up the LX RGB Fan Group
After connecting your LX RGB fans together, insert the iCUE LINK cable (F) into an open active port (I) on one of your LX RGB fans.
Install LX RGB Inside the Case
Mount the LX RGB fans onto your case with the supplied QuikTurn mounting screws (C).
Please note that QuikTurn screws thread much faster than traditional self-tapping screws; we advise only hand-tightening QuikTurn screws with a screwdriver to avoid over-threading your LX RGB fans.
Connect Fan to iCUE LINK System Hub
Connect the power cable (H), Micro-USB cable (G), and iCUE LINK cable (F) into the System Hub (B), then connect the power cable (H) and Micro-USB cable (G) into your power supply and motherboard, respectively.
Mount iCUE LINK System Hub to Your Case
The iCUE LINK System Hub (B) can be magnetically mounted on a steel chassis or adhered to a surface with the supplied mounting tape.
EXPANSION FAN
This section will provide a brief guide on how to install your LX RGB Expansion Fan.
Create or Add Into an Existing Fan Group
Connect the LX RGB Expansion fan into an existing fan group by aligning and inserting the connectors into the open active (I) and passive ports (J).
Connect LX RGB to an iCUE LINK System Hub
Insert the iCUE LINK cable (F) into an open active port (I) on one of your LX RGB fans.
Connect Fan to iCUE LINK System Hub
Connect the iCUE LINK Cable (F) into an available active port (I) on the iCUE LINK System Hub (B - sold separately).
SOFTWARE SETUP
1. Install iCUE
2. Update iCUE
- Once iCUE is installed, run the software. If a newer iCUE version is available or if any of the connected devices need a firmware update, you will be prompted to perform an update via a notification in the top right corner. You can also click the settings (cog wheel icon in the top right corner) and check for the software and firmware updates manually.
3. Quick Lighting Setup
- Select the predefined Murals effects from the iCUE Home screen to quickly change the lighting effects.
4. Configure iCUE - Fan Setup
The Setup page will display all LX RGB fans connected to the System Hub and allow you to re-order them to better match the physical placement inside your system.
- Mouseover the iCUE LINK System Hub tile and select Lighting Setup.
- Select the LX RGB under Lighting Setup to rearrange your fans.
5. Configure iCUE - Fan Lighting
Choose your desired lighting animation from several pre-defined lighting effects.
- Select LX RGB from the navigation bar.
- Click “Lighting Effects” to access the lighting effects page and select the desired lighting effect.
- Click the “+” icon under “Lighting Layers” to add additional lighting effects.
6. Configure iCUE - Fan Performance
Select your desired fan curve presets between Quiet, Balanced, Extreme, or create your own curve.
- Select the LX RGB from the navigation bar.
- Click “Cooling” to access the fan performance page.
- Select the desired fan curve preset for each fan.
- ... or click the “+” icon under “Cooling Presets” to create a custom fan curve.
7. Additional Setup
Visit our CORSAIR LAB for additional iCUE setup, configuration and tips.
FAQ
Why can’t I change my lighting effect?
Murals may be preventing you from selecting a lighting effect. You may disable Murals by clicking on the Murals indicator located on the Home screen or from the iCUE LINK device page.
Does LX RGB support hot-plugging?
The iCUE LINK System Hub and LX RGB fans do not support hot-plugging, but you can quickly detect newly connected devices while your PC is running by doing the following:
- Select the iCUE LINK System Hub in iCUE.
- Click on settings cogwheel.
- Click Start next to Device Enumeration to re-detect all connected devices.
How many fans can be chained through one channel?
Up to twelve (12) LX RGB fans can be chained and connected simultaneously through one (1) channel on the System Hub. Please note that connecting a large number of iCUE LINK devices to a single channel may affect overall LED brightness, depending on the power draw of the devices used.
POWER RATING
System Hub Output rating: 12Vdc 7A (per port)
LX120 RGB Input rating: 12Vdc 0.4A
LX140 RGB Input rating: 12Vdc 0.45A
WARRANTY
iCUE LINK LX RGB Series fans have a 5-year warranty.
LEGAL
© 2024 CORSAIR MEMORY, Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks of CORSAIR in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured.