クイックスタートガイド
CORSAIR iCUE LINK RX MAX FANS
CONTENTS
Expansion
- One (1) Fan
- One (1) iCUE LINK Cable
- Two (2) Connectors
- Four (4) QuikTurn Mounting Screws
- Four (4) AIO Radiator Mounting Screws
- Four (4) Hydro X Series Radiator Mounting Screws
120mm Starter Kit
- Three (3) Fans
- One (1) iCUE LINK System Hub
- Two (2) iCUE LINK Cables
- One (1) Power Cable
- One (1) Micro-USB Cable
- Four (4) Connectors
- Twelve (12) QuikTurn Mounting Screws
- Twelve (12) AIO Radiator Mounting Screws
- Twelve (12) Hydro X Series Mounting Screws
140mm Starter Kit
- Two (2) Fans
- One (1) iCUE LINK System Hub
- Two (2) iCUE LINK Cables
- One (1) Power Cable
- One (1) Micro-USB Cable
- Two (2) Connectors
- Eight (8) QuikTurn Mounting Screws
- Eight (8) AIO Radiator Mounting Screws
- Eight (8) Hydro X Series Radiator Mounting Screws
GETTING TO KNOW YOUR RX MAX FANS
- iCUE LINK RX MAX Fans
- iCUE LINK System Hub
- Power Cable
- AIO Radiator Mounting Screws
- Hydro X Series Radiator Mounting Screws
- iCUE LINK Cable
- QuikTurn Mounting Screws
- USB Cable
- Passive Connector
- Active Bridge Connector
- Passive Port
- Active Port
GETTING TO KNOW YOUR iCUE LINK SYSTEM HUB
- Active Port
- Power Input
- USB Input
- Tach Output
FAN INSTALLATION
BEFORE YOU START
STARTER KIT
This section will provide a brief guide how to install your RX MAX Starter Kit.
Create or Add Into a Fan Group
Connect the RX MAX fan into an existing fan group by aligning and inserting the connectors into the open active port (L) and passive ports (K).
Setting Up the RX MAX Fan Group
After connecting your RX MAX fans together, insert the iCUE LINK cable (F) into an open active port (L) on your RX MAX fan.
Install RX MAX Inside the Case
Mount the RX MAX fans onto your case with the supplied QuikTurn mounting screws (G).
Please note that QuikTurn screws thread much faster than traditional self-tapping screws; we advise hand tightening QuikTurn screws with a screwdriver only to avoid over threading your RX MAX fans.
Install RX MAX on AIO Radiator
When using RX MAX fans with an AIO radiator, please use the included AIO radiator mounting screws (D) as they are slightly longer to accommodate for the increased thickness of the fans.
Install RX MAX on Hydro X Series Radiator
When using RX MAX fans with a Hydro X Series radiator, please use the included Hydro X Series radiator mounting screws (E) as they are slightly longer to accommodate for the increased thickness of the fans.
Connect Fan to iCUE LINK System Hub
Connect the power cable (C), USB cable (H), and iCUE LINK cable (F) into the System Hub, then connect the power cable (C) and USB cable (H) into your power supply and motherboard, respectively.
Mount iCUE LINK System Hub to Your Case
The iCUE LINK System Hub (B) can be magnetically mounted on a steel chassis or adhered to a surface with the supplied mounting tapes.
EXPANSION FAN
This section will provide a brief guide how to install your RX MAX Expansion Fan.
Create or Add Into an Existing Fan Group
Connect the RX MAX Expansion fan into an existing fan group by aligning and inserting the connectors into the open active port (L) and passive ports (K).
Connect RX MAX to iCUE LINK System Hub
Insert the iCUE LINK cable (F) into an open active port (L) on your RX MAX fan.
Connect Fan to iCUE LINK System Hub
Connect the iCUE LINK cable (F) into an available active port (L) on the iCUE LINK System Hub (B) (sold separately).
iCUE SETUP
1. Install iCUE
2. Update iCUE
- Once iCUE is installed, run the software. If a newer iCUE version is available or if any of the connected devices need a firmware update, you will be prompted to perform an update via a notification in the top right corner. You can also click the settings (cog wheel icon in the top right corner) and check for the software and firmware updates manually.
3. Configure iCUE - Fan Setup
The Setup page will display all RX MAX fans connected to the iCUE LINK System Hub and allow you to re-order them to better match the physical placement inside your system.
- Mouseover the iCUE LINK System Hub tile and select Lighting Setup.
- Select the RX MAX under Lighting Setup to rearrange your fans.
4. Configure iCUE - Fan Performance
Select your desired fan curve presets between Quiet, Balanced, Extreme, or create your own curve.
- Select the RX MAX from the navigation bar.
- Click “Cooling” to access the fan performance page.
- Select the desired fan curve preset for each fan.
- ... or click the "+" icon under "Cooling Presets" to create a custom fan curve.
5. Additional Setup
Visit our CORSAIR LAB for additional iCUE setup, configuration, and tips.
CORSAIR DETACHABLE PLATES COMPATIBILITY
RX MAX fans are compatible with CORSAIR detachable decorative plates (sold separately).
FAQ
Does RX MAX support hot-plugging?
The iCUE LINK System Hub and RX MAX fans do not support hot-plugging but you can use “Device Enumeration” in the iCUE LINK System Hub device settings to force iCUE LINK device re-enumeration without a power cycle.
How many fans can be chained through one channel?
Up to twelve (12) RX MAX fans can be chained and connected simultaneously through one (1) channel on the System Hub.
POWER RATING
System Hub Output Rating: 12Vdc 7A (per port)
RX MAX Input Rating: 12Vdc 0.18A
RX MAX Input Rating: 12Vdc 0.25A
WARRANTY
iCUE LINK RX MAX Series fans have a 5-year warranty
LEGAL
© 2024 CORSAIR MEMORY, Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks of CORSAIR in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured.