CORSAIR XENEON 27QHD240 OLED 27-INCH GAMING MONITOR

Product Setup, User Information, and Warranty/Dead Pixel policy can be found at https://qsg.corsair.com/xeneon-monitors

• Only use the accessories that are provided with the monitor or that recommended by the manufacturer.
• Keep the plastic packaging bag for the product in a place that cannot be reached by children.
• Before connecting the monitor to the power outlet, make sure that the voltage rating of the power cable is compatible with the power specification in the country where you are located.
• The power cord plug must be connected to a properly wired and grounded power outlet.
• Do not touch the plug with wet hands, otherwise can easily cause electric shock.
• Place the monitor in a stable and well-ventilated place.
• Do not place the monitor near any heat sources such as electric radiators or direct sunlight.
• The holes or openings on the monitor are for ventilation. Do not cover or block the ventilation holes with any objects.
• Do not use the monitor near water, drinks, or any type of liquids. Failure to do so may result in electric shock or damage to the monitor.
• Make sure to unplug the monitor from the power outlet before cleaning.
• As the screen surface can be easily scratched, avoid touching the surface with any hard or sharp object. Use a soft lint-free cloth instead of a tissue to wipe the screen. You may use a glass cleaner to clean the equipment if required. However, never spray the cleaner directly onto the screen.
• Disconnect the power cable if the equipment is not being used for a long period of time.
• Do not attempt to disassemble or repair the monitor yourself.
• Please remove the protective film on the screen of the product before use.
• When the product is running or turning off, please do not unplug the power adapter.
  • If the adapter is unplugged accidentally, horizontal line noise could occur momentarily.
  • Please run “Image Retention Refresh” if you have the horizontal line noise.
    (OSD/System Setting/Image Retention Refresh)

A. CORSAIR XENEON 27QHD240 OLED Display Panel
B. Stand Base
C. AC Adaptor
D. AC Power Cable
E. DisplayPort Cable (1.5M)
F. HDMI Cable (1.5M)
G. USB-C Cable (1.5M)
H. USB-A to USB-C cable (1.8M)

1. Cut the tape on the top of the box, open flaps and lay the box down with the hand cutout opening towards the top.  Take hold of hand opening and slide foam out of carton.
2. Remove base and center foam insert.
3. Remove stand neck from the other section of foam packaging.
4. Lift off top section of foam and set aside.  This section contains the AC Adapter and accessory cables.  The bottom section of foam contains the monitor panel.
5. Align the 3 fingers on the top of the stand neck with the 3 notches in the top section of the VESA mount section.  Angle the 3 fingers into the notches and lower into place until you hear an audible click and it is secure.  Notice the push button on the bottom of the connector plate.  Press down on this button and lift the stand neck up if you need to remove it in the future.  This is where you will mount to a compatible VESA wall or desk mount. Pickup the stand base and align it to the bottom of the stand neck and press it into place.  Lift up the key on the captive thumbscrew and turn it clockwise with your fingers until the base is secured to the stand neck.
6. Pick up the monitor by the stand neck and set it upright on your desk.  You can now connect it up to your devices.

CORSAIR XENEON 27QHD240 OLED features a sturdy and stylish stand that offers several adjustments below down

• Tilt -7/+15 degrees
• Height +/- 100mm

• Swivel +/- 30 degrees

• Pivot +/- 90 degrees

Reach your hand here on the front of the unit and there will be a Button Location Indicator popping up on the screen for user's reference. This indicator activates when movement is detected within 25-50mm of the buttons. The indicator will turn off after 5 seconds.

Your monitor includes a joystick on the front-bottom side for opening shortcuts and navigating display settings.

By pressing the joystick inward, you can access your monitor’s display settings. You can use the joystick to navigate the settings and pressing the joystick inward will confirm your selection.

The first menu, labeled “Picture”, contains the following settings for adjusting the overall picture quality.

The second menu, labeled “PIP/PBP”, lets you enable the PIP/PBP functions and display different ways.

The third menu, labeled “OSD Setting”, contains the following settings for adjusting the display’s internal settings.

The fourth menu, labeled “System Setting”, lets you make adjustments to the system settings.

The fifth menu, labeled “Audio”, lets you control the display’s audio.

The sixth menu, labeled “Input Source”, lets you switch between the display’s different inputs.

The seventh menu, labeled “Information”, provides you monitor information.

1. Remove Stand Neck by pressing down on lock button underneath the neck hinge.
2. Lift up and remove the stand.
3. Attach compatible 100mm x 100mm VESA mount after ensuring weight and size support.