CORSAIR iCUE LINK XD5 RGB ELITE PUMP RESERVOIR COMBO

Please download the latest version of iCUE from www.corsair.com/downloads

Learn more about iCUE LINK System Hub from CORSAIR iCUE LINK System Hub.

Place the XD5 RGB ELITE on the mounting bracket (B) with un-threaded holes facing up. Secure the XD5 RGB ELITE to the bracket using four M3x6mm screws (J) from the bottom.

Secure the XD5 RGB ELITE with the installed pump-reservoir mounting bracket onto a 120mm or 140mm fan mounting adapter plate (C) using four M3 thumb screws (K). The fan adapter brackets can be mounted horizontally or vertically thus allowing free movement in horizontal and vertical axis (depending on orientation).

With the pump-reservoir unit  already mounted to a fan mounting adapter secure the assembly to the radiator with the short 6mm (0.25") M4xP0.7 screws supplied with the CORSAIR XR radiator itself.

With the pump-reservoir unit  already mounted to a fan mounting adapter secure the assembly to the radiator using four enclosed self-tapping fan screws (F).

Secure the XD5 RGB ELITE with the fan mounting adapter bracket onto a case fan opening. Use enclosed M4x6mm screws (I) along with M4 washers (H) and M4 nuts (G).

Locate the suitable cut-out hole pattern in the chassis that would fit 55mm x 27.5mm (for vertical installation) or 55mm x 67mm (for horizontal installation) hole pattern.

The XD5 RGB ELITE must be installed vertically with the pump below the reservoir tube.

1. Install the two (2) appropriate CORSAIR XF G1/4" BSPP threaded-type fittings (not included) into the reservoir ports and tighten them by hand. Do not use any tools (i.e. pliers).
2. It is mandatory to use the front-left port as the OUTLET port and any other bottom port as inlet. The recommended INLET (return) port is marked on the image below. Optionally, you can use the top G1/4" port with integrated tube as an INLET (return) line as well.

Please download the latest version of iCUE from www.corsair.com/downloads

You must have an iCUE LINK SYSTEM HUB to use the XD5 RGB ELITE pump/reservoir. Connect the included 90 degree iCUE LINK cable from the iCUE LINK header on the pump housing to an iCUE LINK System Hub.

The XD5 RGB ELITE pump/reservoir can be used with other iCUE LINK hardware by placing it anywhere on the channel string using a direct connection, Y cable accessory, or 4-way splitter.

1. Make sure the PSU is turned OFF, either at the plug socket, or via the toggle switch on the rear of the PSU (Figure 1).
2. Disconnect PSU power cables from all computer components except the iCUE LINK System Hub 6 pin PCIe power connector.
3. Connect the enclosed ATX 24-pin PSU Jumper Bridge starter (D) to your PSU 24-pin ATX cable. This will allow you to power on your iCUE LINK System Hub and all devices connected to the System Hub without powering on the PC (Figure 2).
   

Move the manual pump speed override switch on the side of the XD5 RGB ELITE pump/reservoir to position 1. This will allow the pump to run at full power, allowing for easier priming and bleeding of air.

1. Fill the reservoir through the top left G1/4" opening with CORSAIR coolant using a filling flask to about 2cm (4/51 below the top).
2. Turn on the power by flipping the ON switch on the PSU. The pump motor will be primed with coolant from the reservoir and will start flowing through the system. Turn the power OFF before the reservoir is emptied. Do not let the pump run dry or without coolant in the reservoir as this will damage the pump.
3. Repeat steps 1 and 2 until your custom cooling system is full. CORSAIR recommends not to fill the reservoir more than about 2cm from the top.

4. Move the manual override pump speed switch back to position 2 on the pump housing once priming the loop is complete. You will not be able to control pump speed and it will run at priming speed if not set back to its original position.

5. Once the system is filled with coolant, CORSAIR recommends running it for 24 hours to remove any air trapped in the components and to make sure there are no leaks in the system. Once you have thoroughly leak-tested the system, turn OFF the PSU (Figure 1) and disconnect the ATX 24-pin PSU Jumper Bridge (Figure 2). Reconnect the power cables to other computer peripherals and start the computer.

HYDRO X Series Core products (CPU and GPU Blocks, Pumps, and Radiators) have a 3-year warranty.

© 2023 CORSAIR MEMORY, Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks of CORSAIR in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured.