MANUAL | QUICK START GUIDE

CORSAIR ONE

CORSAIR_ONE_i500_DARK_WOOD_RENDER_04
CORSAIR_ONE_i500_BRIGHT_WOOD_RENDER_043

CORSAIR ONE INTRODUCTION

Thank you for purchasing the CORSAIR ONE!


CORSAIR ONE CONTENTS

Corsair One Top Sheet Edited
Corsair One WIFI Antennas

TOP SHEET

WIFI ANTENNAS

Corsair One Power Cable

POWER CABLE


CORSAIR ONE CONNECTIVITY

Corsair One Connectivity - Front View_Edited
  1. POWER
  2. 3.5mm Audio Combo Jack
  3. USB 3.2 Type-A (Gen1)
  4. USB 3.2 Type-C (Gen 2)
Corsair One Connectivity - Rear View
  1. USB 2.0
  2. HDMI
  3. DisplayPort
  4. USB 3.2 Gen 2x2 Type-C
  5. USB 3.2 Gen 2 Type-A
  6. USB 3.2 Gen 2 Type-A
  7. LAN Port
  8. WIFI / Bluetooth
  9. 7.1 HD Audio Connector
  10. HDMI (on GPU)
  11. Display Port (on GPU)
  12. Power Supply Connector

Note: Port Connections and placements may vary based on installed motherboard.


SETTING UP YOUR CORSAIR ONE

UNBOXING THE CORSAIR ONE

The CORSAIR ONE is bundled with a power supply power cord and the WIFI antennas that will be installed on the rear side of the desktop. Before powering on, make sure to connect all your devices so they are readily available when the system is powered on.

  1. Safely remove the CORSAIR ONE from its packaging.
  2. Remove the top and bottom protective shipping inserts from the CORSAIR ONE.
  3. Place your CORSAIR ONE on your desk to continue the set-up process. If you prefer to place the CORSAIR ONE on the floor, avoid placing it on shaggy carpets as this can cause heating issues. For the best results, make sure the CORSAIR ONE is elevated off the floor.

CONNECTING THE CORSAIR ONE

  1. Connect your mouse and keyboard, as well as any other devices, to the desktop via the USB ports on the motherboard located on the rear side of the case.
Connecting the Corsair One 1

2. Connect your monitor to the graphics card using either an HDMI or Display Cable.

Connecting the Corsair One 2

3. Attach the WIFI antennas to the WIFI ports available on your system. If you prefer to use an Ethernet cable for Internet access, plug the ethernet cable instead.

Connecting the Corsair One 3

4. Connect the power cable into the power supply and then connect the other end of the power cable to the nearest power outlet. If you are using a surge protector, connect the power cable to the surge protector instead.

5. Turn the power supply switch on and press the power button located on the front panel of the CORSAIR ONE.

Connecting the Corsair One 5

6. Once the system goes through the initial boot process, it will load the pre-installed Windows operating system.

7. Follow along the Windows prompts to complete the user account creation.


CORSAIR ONE LIGHTING FEATURES

FRONT PANEL CONTROLS

The lighting for CORSAIR ONE can be controlled using the touch sensitive strip located on the front panel. The top section of the strip changes the active color of the lighting, and the bottom section of the strip controls the RGB effect and brightness levels. For more information, view the video below, and follow the listed instructions.

Front Panel Control

Front Panel Controls


RELEASE NOTES

Sliding your finger upwards and downwards on the top section of the front panel strip will actively change the RGB color of the CORSAIR ONE.
Note: This feature only works in the Static RGB effect.

Corsair One Front Panel Top Control
  1. Red
  2. Orange
  3. Yellow
  4. Green
  5. Blue
  6. Indigo
  7. Violet
  8. White

Pressing the bottom section of the front panel strip for approximately 2 seconds, will actively change the RGB effect

Corsair One Front Panel Bottom Control
  1. Static
  2. Breathing
  3. Strobing
  4. Color Cycle
  5. Rainbow
  6. Starry Night

Sliding your finger upwards and downwards on the bottom section of the front panel strip will actively change the brightness levels of the CORSAIR ONE lighting. Pressing the bottom section for approximately 5 seconds will turn the lighting strips off. Repeating this action will turn them back on.

Front Panel Bottom Control Brightness Level2

REAR PANEL LIGHTING

The rear side of CORSAIR ONE has built-in, motion sensing LEDs to actively light the rear I/O connections for easy visibility. When the sensor detects motion, the rear lighting will turn on and remain on for 20 seconds before turning off. If you would like manual control of the lighting, you can tap the top section of the rear panel to turn the light On and Off.

Corsair One Rear Panel Lighting

CORSAIR ONE DASHBOARD

NAVIGATING THE CORSAIR ONE DASHBOARD

The CORSAIR ONE DASHBOARD provides more functionality to the CORSAIR ONE lighting features. The dashboard provides a wide array of colors to choose from, quick options for changing the RGB effect, and provides real time RPM data for your fans and cooler, and temperatures of your GPU and CPU.

CORSAIR ONE DASHBOARD

The homepage of the Dashboard provides access to all the CORSAIR ONE lighting changes, Coolant Temperature readings, and RPM speeds for your Cooler and Fans. The Dashboard also contains the link to the CORSAIR ONE Quick Start Guide.

Corsair One Dashboard

ACTIVE RGB EFFECT

Clicking on the Active RGB Effect visual will open a dialog box with various options to quickly activate a different visual effect.

Corsair One Active RGB Effect Dashboard

Selecting any of the RGB effects will actively change the Lighting Effect on the CORSAIR ONE.

Corsair One RGB Effect

ACTIVE RGB COLOR

Clicking on the Active RGB Color visual will open a new window with various options to quickly change the color of the CORSAIR ONE.

Corsair One Active RGB Color Dashboard

You can select any color from the color wheel or enter a specific color code in the color code section.
Note: Changing the color only applies to the “Static” RGB Effect.

Changing RGB Color

When a new color is selected, the Corsair One will actively change RGB Color, and the Dashboard background will change color.

Corsair One Brightness Level

ACTIVE BRIGHTNESS LEVEL

The brightness level of the CORSAIR ONE lighting can be actively adjusted by moving the brightness level bar left or right.

Corsair One Active Brightness Level

SYSTEM SETTING

Clicking on the cog wheel located on the top right corner of the CORSAIR ONE DASHBOARD will open a new window listing the CORSAIR ONE specifications in the “General” tab.

Corsair One System Information and Software Update

The “Software Update” section of the System Settings will display the Current Version of the CORSAIR ONE DASHBOARD, Last Checked for updates date, and Available Version (if available). Clicking on “Check for Update” button will check for the latest update.

Corsair One Latest Software Update

CORSAIR DIAGNOSTIC

CORSAIR ONE includes the CORSAIR DIAGNOSTICS utility software that provides an overview of your CORSAIR ONE, diagnoses and evaluates your components, reports any issues that may have occurred on your desktop, shows an overview of installed applications, and more. Follow the instructions below to access all the CORSAIR DIAGNOSTICS features.

HOME PAGE

CORSAIR DIAGNOSTICS is located on your desktop.

Corsair One Corsair Diagnostics

The homepage will show your purchased CORSAIR ONE and display all the features available in CORSAIR DIAGNOSTICS.

Corsair One Homepage

ANALYSIS

In the Analysis feature, you can evaluate individual components to ensure they are functioning properly, or can you test all the components at once for a full quality evaluation. The test can be configured to loop one time or have multiple loops for extended testing.

Corsair One Analysis Active Test

When the test is complete, you will be prompted with a Pass/Fail notice, number of loops completed, and the time it took for the test to complete.

Corsair One Analysis Complete

Clicking on the “Go To Results” button will redirect you to the full results of the evaluation. The results will display each test that was executed on the component with a Pass/Fail notification.

Corsair One Analysis Results

CHECK UP

In the Check Up feature, you can perform stress tests on your components. This can be done in sequential order, or you can stress test all the components at once. To begin, choose either “Simultaneously” or “Sequentially” and begin the Checkup Test.

Corsair One Checkup Active Test

When the test is complete, you will be prompted with a Pass/Fail notice, and the time it took for the test to complete.

Corsair One Checkup Complete

Clicking on the “Go To Results” button will redirect you to the full results of the evaluation. The results will display each test that was executed on the component with a Pass/Fail notification.

Corsair One Checkup Results

INTERACTIVE TESTS

In the Interactive Tests feature, you can check the functionality of your connected devices and verify that they are working properly. Select a device, and follow the instructions provided to evaluate the connected device.

Corsair One Interactive Tests Homepage

The mouse test will evaluate the functionality and accuracy of your connected mouse.

Corsair One Interactive Tests Mouse

The keyboard test will evaluate the functionality and accuracy of your connected keyboard.

Corsair One Interactive Tests Keyboard

The GPU test is an interactive test that will evaluate your installed graphics card. Follow along the instructions provided in this section to complete the GPU test. After stopping the test, you must select “Pass” or “Fail” to add the results to the report.

Corsair One Interactive Tests GPU

SYSTEM INFO

The System Info section provides your system’s full hardware and software information with its configuration and layout. It also provides a detailed log of any events that have occurred on your CORSAIR ONE.

Corsair One System Info

WINDOWS SUPPORT

The Windows Support feature provides assorted options to optimize Windows settings on your CORSAIR ONE. These options include optimizing your storage drives, setting optimal power options, personalizing your desktop, and more.

Corsair One Windows Support

EVENTS CALENDAR

In the Events Calendar section, you can view error logs and application events that have occurred on your CORSAIR ONE. This will be illustrated in the calendar by colored squares based on the severity of the event.

Corsair One Event Calendar

UPGRADING COMPONENTS

CORSAIR ONE is configured with a micro ATX form-factor motherboard making future upgrades hassle-free. If you purchase extra storage or memory to expand your CORSAIR ONE capabilities, you can easily follow along our step-by-step instructions for easy installation.

MEMORY INSTALLATION

To change or install more memory, follow the instructions listed below.

  1. Remove the Left Side Panel Filter by gently pulling the filter away from the side panel.
Corsair One Memory Installation Remove Side Panel Filter

2. Remove the 2x Screws from the side panel, then remove the side panel to get to the internals.

Corsair One Memory Installation Remove Screws

3. To access the Motherboard, CPU, and Memory, remove the 2x screws shown below to open the fan bay. Then swing open the fan bay to access the components.

Corsair One Memory Installation Motherboard Access

4. To access the memory slots, carefully move the Liquid Cooling tubes aside to allow room to install the memory.

Corsair One Memory Installation Move Liquid Cooling Tube

5a. To add more memory to the existing configuration, install the new memory in the 1st and 3rd memory slots. To do so, push the top-notch on memory slot, and install the memory firmly until you see the top-notch snap back into place.

Corsair One Memory Installation Add More Memory

5b. To change the memory, push the top- notches of the memory slots to release the existing memory. Then remove the memory and install the new memory sticks in the 2nd and 4th memory slots for 2x stick configurations, or all four slots for 4x stick configurations. When installing the new memory, ensure you firmly press the memory sticks into the slots until you see the top-notch snap back into place.

6. After completing installation, make sure to close the fan bay, and reinstall the screws in their respective locations.

Corsair One Memory Installation Motherboard Access

7. Replace the side panel and reinstall the screws in their respective locations

Corsair One Memory Installation Reinstall Screws

8. Replace the Left Side Panel Filter by aligning the magnets with the case.

Corsair One Memory Installation Replace Left Side Panel Filter

NVMe M.2 SSD STORAGE INSTALLATION

To install additional Storage, follow the instructions listed below.

  1. Remove the Left Side Panel Filter by gently pulling the filter away from the side panel.
Corsair One Memory Installation Remove Side Panel Filter

2. Remove the 2x Screws from the side panel, then remove the side panel to get to the internals.

Corsair One Memory Installation Reinstall Screws

3. To access the Motherboard, CPU, and Memory, remove the 2x screws shown below to open the fan bay. Then swing open the fan bay to access the components.

Corsair One Memory Installation Motherboard Access

4. To install an additional NVMe m.2 SSD (storage device), carefully move the Liquid Cooling tubes aside to allow room for installation.

Corsair One Memory Installation Move Liquid Cooling Tube

5. Remove the 2x screws from the heatsink to remove the cover and access the m.2 slot on the motherboard.

Corsair One NVMe M.2 SSD Remove Screws

6. Install the NVMe m.2 SSD (storage device) into the slot. Replace the heatsink cover onto the NVMe m.2 SSD (storage device), and secure with the 2x screws that were removed in the previous step.

7. After completing installation, make sure to close the fan bay, and reinstall the screws in their respective locations.

Corsair One Memory Installation Motherboard Access

8. Replace the side panel and reinstall the screws in their respective locations.

Corsair One Memory Installation Reinstall Screws

9. Replace the Left Side Panel Filter by aligning the magnets with the case.

Corsair One Memory Installation Replace Left Side Panel Filter

2.5" SSD STORAGE INSTALLATION

To install additional storage, follow the instructions below.

  1. Remove the Right Side Panel Filter by gently pulling the filter away from the side panel.
Corsair One SSD Storage Installation Right Side Panel Filter

2. Remove the 2x Screws from the side panel, then remove the side panel to get to the internals

Corsair One Memory Installation Remove Screws

3. Remove the 2x screws on the 2.5” drive cage brackets and install the brackets onto the 2.5” SSD storage drive with the pre-installed screws provided.

Corsair One SSD Storage Installation Remove Screws

4. Plug in the SATA power cable and SATA data cable into the 2.5” storage drive. These cables are prewired for easy installation. Reinstall the 2.5” drive cage brackets onto CORSAIR ONE with the 2x screws previously removed.

Corsair One SSD Storage Installation SATA Power Cable

5. After completing installation, make sure to replace the side panel, and reinstall the screws in their respective locations

Corsair One Memory Installation Remove Screws

6. Replace the Right Side Panel Filter by aligning the magnets with the case.

Corsair One SSD Storage Installation Right Side Panel Filter

PCIe DEVICE INSTALLATION

CORSAIR ONE is configured with a mATX motherboard that provides an additional PCIe slot for expansion cards. To access this additional PCIe slot, follow the instructions listed below. This slot is compatible with many x4 single-slot PCIe cards. See our support page for tested cards.

  1. Remove the Left Side Panel Filter by gently pulling the filter away from the side panel.
Corsair One Memory Installation Remove Side Panel Filter

2. Remove the 2x Screws from the side panel, then remove the side panel to get to the internals

Corsair One Memory Installation Reinstall Screws

3. Remove the 3x screws installed on the PSU shield, and the 1x screw installed the bottom fan to gain access to the PCIe slot.

Corsair One PCle Device Installation Remove Screws2

4. Before installing the expansion card, push the PCIe slot notch, and then install the expansion card by pushing the card firmly into the slot until see the notch snap back into place.

Corsair One PCle Device Installation Expansion Card

5. After completing installation, make sure to reinstall the PSU shield and fan, and reinstall the screws in their respective locations.

Corsair One PCle Device Installation Remove Screws2

6. Replace the side panel and reinstall the screws in their respective locations

Corsair One Memory Installation Reinstall Screws

7. Replace the Left Side Panel Filter by aligning the magnets with the case.

Corsair One Memory Installation Replace Left Side Panel Filter

USB CONNECTIVITY

The USB ports on the motherboards vary in speed and connectivity features. To learn more about USB connectivity and features, follow the link below:

ELGATO CAPTURE CARD

HOW TO SET UP ELGATO CAPTURE CARDS WITH OBS STUDIO

HOW TO SET UP XBOX SERIES X|S WITH ELGATO 4K60 PRO MK.2

HOW TO SET UP ELGATO 4K60 PRO MK.2 WITH NINTENDO SWITCH

ESG INITIATIVE

At Corsair, we are committed to delivering premium, high-performance computer systems to our customers while also prioritizing environmental sustainability. That's why we've designed an innovative packaging solution that combines the reliability of recycled Expanded Polyethylene (EPE) foam with the eco-friendly benefits of oyster shell material.

KEY FEATURES

Uncompromised Protection: Our packaging solution provides exceptional cushioning and support to ensure that your high-performance computer systems arrive at their destination in pristine condition. Through rigorous testing, including ISTA6A drop test requirements, we guarantee that the products will be safeguarded against the rigors of transportation and handling.

Environmental Responsibility: By utilizing recycled EPE foam (100% Post-Consumer Recycled) and 30% oyster shell material, we're taking significant steps towards reducing our environmental footprint. These materials not only offer superior protection but also contribute to waste reduction and promote the use of sustainable resources. We also utilize a one-color print design instead of high-gloss, multi-colored box to align with our commitment to environmental responsibility.

Compliance and Assurance: We understand the importance of meeting industry standards and regulatory requirements. That's why our packaging solution is designed to comply with ISTA6A drop test standards as well as the strict shipping guidelines of leading carriers such as FedEx and UPS. With our packaging, you can have peace of mind knowing that your products are in safe hands from dispatch to delivery.

BENEFITS

  • Superior protection for high-performance computer systems
  • Environmentally mindful using recycled materials
  • Compliance with industry standards and shipping regulations

CONCLUSION

At Corsair, we believe that sustainability and performance can go hand in hand. With our innovative packaging solution featuring recycled EPE foam and oyster shell material, we deliver premium products to our customers with confidence, knowing that we're making a positive impact on the environment. Our environmentally conscious packaging allows you to experience the perfect blend of protection, sustainability, and peace of mind.

ONE TREE PLANTED

With the partnership with One Tree Planted, Corsair is donating $1 for every Corsair One unit sold. One Tree Planted mission is to support reforestation efforts across the globe with its extensive network of quality planting partners. One Tree Planted plants trees in areas that have been devastated by fire, drought, and floods among other causes (“Project(s)”). Benefits to tree planting programs include increasing wildlife biodiversity; improving air and water quality; improving soil health; providing jobs in local communities; and restoring community well-being.

ACCESSING THE LATEST SETUP AND DOCUMENTATION

ACCESSING DRIVERS AND SOFTWARE

CORSAIR ONE comes with all the necessary drivers and software preinstalled for operation. New versions of drivers and software are available on Corsair.com product support page.

COMPLIANCE STATEMENT

LIMITED PRODUCT WARRANTY

REMEDIES

OBSOLETE OR DISCONTINUED PRODUCTS

EXCLUSIONS

COPYRIGHT/LEGAL INFORMATION

LIMITATION OF LIABILITY

Vengeance PC Web QSG - 2 Year Warranty Logo